A worthwhile project completed
Posted: Wed Nov 18, 2009 9:30 pm
No its not dyslexia.
I just thought some of the Tubenet folk would find this of some interest.

Early last year, I received a phone call from a gentleman who had tragically suffered a stroke that had left him minimal use of his right hand. I am sure many of us can imagine the impact this would have on our life and the ability to play our instruments. The caller was desperately searching for someone who could provide him with an instrument suitable for his playing needs. I suggested a few manufacturers, he informed me that he had already corresponded with them and they were ether unable or unwilling to provide what he desired. The repair shops he contacted were for the most part not very interested for a number of reasons I can completely understand. His need was for a left hand or reversed baritone horn. To be honest, I was not real interested in taking on the task myself with all the projects I had on my bench at the time but after discussing the matter and thinking how upset I would be if I were in the same boat, I agreed to consider the task and eventually accepted the challenge. The original instrument for the project that I received from the owner was one he got off eBay. It was an old King 2268 that had been beat to crap and really badly overhauled and then beat to crap again. Much of the instruments parts were junk that I quickly tossed into the scrap can.

The important part that was salvageable was the valve section which is probably the best one available for such a conversion. The ports were removed, the forth valve cut off and refit and brazed to the first valve. The porting of the first and third valves are so close that with a bit of skill and a little care the block was able to be completely reversed to a mirror image of its original configuration. There were a lot of small alterations along with a good deal of repair work to the casings, pistons and slide tubes but in the end it turned out pretty decent. You can't simply slap these together and it did require a lot of effort but in the end I felt the project to be really interesting and worth the time spent.
Daniel C. Oberloh
Oberloh Woodwind and Brass Works
http://www.oberloh.com" target="_blank" target="_blank"
I just thought some of the Tubenet folk would find this of some interest.

Early last year, I received a phone call from a gentleman who had tragically suffered a stroke that had left him minimal use of his right hand. I am sure many of us can imagine the impact this would have on our life and the ability to play our instruments. The caller was desperately searching for someone who could provide him with an instrument suitable for his playing needs. I suggested a few manufacturers, he informed me that he had already corresponded with them and they were ether unable or unwilling to provide what he desired. The repair shops he contacted were for the most part not very interested for a number of reasons I can completely understand. His need was for a left hand or reversed baritone horn. To be honest, I was not real interested in taking on the task myself with all the projects I had on my bench at the time but after discussing the matter and thinking how upset I would be if I were in the same boat, I agreed to consider the task and eventually accepted the challenge. The original instrument for the project that I received from the owner was one he got off eBay. It was an old King 2268 that had been beat to crap and really badly overhauled and then beat to crap again. Much of the instruments parts were junk that I quickly tossed into the scrap can.

The important part that was salvageable was the valve section which is probably the best one available for such a conversion. The ports were removed, the forth valve cut off and refit and brazed to the first valve. The porting of the first and third valves are so close that with a bit of skill and a little care the block was able to be completely reversed to a mirror image of its original configuration. There were a lot of small alterations along with a good deal of repair work to the casings, pistons and slide tubes but in the end it turned out pretty decent. You can't simply slap these together and it did require a lot of effort but in the end I felt the project to be really interesting and worth the time spent.
Daniel C. Oberloh
Oberloh Woodwind and Brass Works
http://www.oberloh.com" target="_blank" target="_blank"