Anybody have a lead on *good* jeweler's saw blades?
I'm sick and tired of them breaking before they have a chance to become dull.
Jeweler's saw blades
- roweenie
- pro musician
- Posts: 2165
- Joined: Mon Mar 05, 2007 10:17 am
- Location: Waiting on a vintage tow truck
Jeweler's saw blades
"Even a broken clock is right twice a day".
- Dan Schultz
- TubaTinker
- Posts: 10424
- Joined: Thu Mar 18, 2004 10:46 pm
- Location: Newburgh, Indiana
- Contact:
Re: Jeweler's saw blades
Rio Grande Jewelry Supply?
Dan Schultz
"The Village Tinker"
http://www.thevillagetinker.com" target="_blank
Current 'stable'... Rudolf Meinl 5/4, Marzan (by Willson) euph, King 2341, Alphorn, and other strange stuff.
"The Village Tinker"
http://www.thevillagetinker.com" target="_blank
Current 'stable'... Rudolf Meinl 5/4, Marzan (by Willson) euph, King 2341, Alphorn, and other strange stuff.
- roweenie
- pro musician
- Posts: 2165
- Joined: Mon Mar 05, 2007 10:17 am
- Location: Waiting on a vintage tow truck
Re: Jeweler's saw blades
Are these the ones that you had mentioned previously? I think I'll order some and check them out.the elephant wrote:I have really liked these over what I had recently been getting from either Ferree's or Allied.
Pike 6/0 Saw Blades
I dont like to work with a blade that is too fine. How fine (or coarse) is 6/0? (I must admit that the numbering system has always been a bit of a mystery to me )
"Even a broken clock is right twice a day".
- roweenie
- pro musician
- Posts: 2165
- Joined: Mon Mar 05, 2007 10:17 am
- Location: Waiting on a vintage tow truck
Re: Jeweler's saw blades
I was looking at the Ferree's website, and they have numbers 0, 2, 4, and 6, six being the coarsest, so maybe 6/0 is a coarse thread?
They're inexpensive enough, maybe I'll order several different ones, or the sampler, as you suggested.....
They're inexpensive enough, maybe I'll order several different ones, or the sampler, as you suggested.....
"Even a broken clock is right twice a day".
- roweenie
- pro musician
- Posts: 2165
- Joined: Mon Mar 05, 2007 10:17 am
- Location: Waiting on a vintage tow truck
Re: Jeweler's saw blades
Now, now, fellas.....
I'm really not yet sure what will work best for me. The fine kerf blades I've been using so far are so miserably weak that they snap almost immediately. The only reason I've settled into heavier blades is because the extra mass makes them less likely to break.
If I had a fine blade that had some strength, they might be a better option, but I just don't know yet.
(Damn, I really need to get a lathe - I waste a lot of time cutting tubing this way...... )
I'm really not yet sure what will work best for me. The fine kerf blades I've been using so far are so miserably weak that they snap almost immediately. The only reason I've settled into heavier blades is because the extra mass makes them less likely to break.
If I had a fine blade that had some strength, they might be a better option, but I just don't know yet.
(Damn, I really need to get a lathe - I waste a lot of time cutting tubing this way...... )
"Even a broken clock is right twice a day".
- roweenie
- pro musician
- Posts: 2165
- Joined: Mon Mar 05, 2007 10:17 am
- Location: Waiting on a vintage tow truck
Re: Jeweler's saw blades
the elephant wrote:This company makes very decent blades.
"Even a broken clock is right twice a day".