Conn 36J?

edsel585960 · Post by **edsel585960** » Tue Aug 04, 2015 11:20 am

I'm thinking it is a 36j too.

edsel585960 · Post by **edsel585960** » Tue Aug 04, 2015 11:22 am

I actually was just pulling up Tubenet to post the same tuba and ask if it was a 36j and there was your post at the top of the page. SPOOKY!

Dan Schultz · Post by **Dan Schultz** » Tue Aug 04, 2015 12:29 pm

lost wrote:It's not oversized. Full size 4/4 most likely.

Yes... it's a 4/4 Conn. Not the large bore of the short-action 2XJ tubas.

Actually... that appears to be a 2XJ body case. You don't normally see the leadpipe on the hinge side.

edsel585960 · Post by **edsel585960** » Tue Aug 04, 2015 6:16 pm

Seller got back to me. Serial # 284566, 6 1/4 bell opening.

groovlow · Post by **groovlow** » Wed Aug 05, 2015 5:44 pm

I thought it looked like a "Donatelli" in BBb +detachable bell.

Timswisstuba · Post by **Timswisstuba** » Wed Aug 05, 2015 8:27 pm

I have one of these tubas and it's similar in size to 4/4 Kings. The small end of the Conn bell is a bit bigger than those of 4/4 King tubas. A King bell will just slip into the 4/4 Conn but the Conn bell will not work on the King.

Timswisstuba · Post by **Timswisstuba** » Wed Aug 05, 2015 9:51 pm

bloke wrote:
Timswisstuba wrote:I have one of these tubas and it's similar in size to 4/4 Kings. The small end of the Conn bell is a bit bigger than those of 4/4 King tubas. A King bell will just slip into the 4/4 Conn but the Conn bell will not work on the King.
How flat (or "remarkably dead-on pitch") is the 3rd partial F and E-natural ?

Not sure about the 3rd partial because the horn is on another continent than I am and it needs a valve job and leadpipe. I experimented putting the horn in CC by using other branches and I can safely say it's a much better horn in BBb than in CC.

Timswisstuba · Post by **Timswisstuba** » Wed Aug 05, 2015 9:58 pm

bloke wrote:Recordabbelli ?

Yes, it's a Recorda(beer)belli..
..but only a 4/4 belli. not the full grown 26J/ 36J bratwurst belli!

Dan Schultz · Post by **Dan Schultz** » Wed Aug 05, 2015 10:34 pm

bloke wrote:Does anyone in tubenet-land have a detachable CONN bell with a 6-1/4" bell...??

Isn't 6" the most common for 4/4 ?

The guy probably measured the OUTSIDE of the receiver! This is a 4/4 horn. There's a way big difference to get to the 7 1/4" tenon on the 2XJ tubas.

edsel585960 · Post by **edsel585960** » Mon Aug 24, 2015 1:35 am

So did anyone on here get it? Was it as nice as it looked? Plays well? The guys you outbid want to know.

TubeNet

Conn 36J?

Re: Conn 36J?

Re: Conn 36J?

Re: Conn 36J?

Re: Conn 36J?

Re: Conn 36J?

Re: Conn 36J?

Re: Conn 36J?

Re: Conn 36J?

Re: Conn 36J?

Re: Conn 36J?