Fingering chart for CC
-
Sean Kennedy
- lurker

- Posts: 13
- Joined: Sun Jun 11, 2006 11:09 pm
- Location: Albuquerque, NM/Santa Fe, NM
Fingering chart for CC
I need a finigering chart, or a link to one, that shows a tuba with a 5th valve that goes a step and a half. E-mail me at tubamaster_1@yahoo.com.
- iiipopes
- Utility Infielder

- Posts: 8580
- Joined: Tue Sep 06, 2005 1:10 am
Do you really mean the flat whole step? I don't believe 5th valves are made to a full step and a half, unless you have the slide pulled way, way out, as that is what 12 or 3 is usually for, of course. Some older thumb valves are the equivalence of 23, which is two whole steps, to fill in the gap between 3 and 4 to have a single valve do the Major 3rd interval down.
What is your tuba? That might shed more light. Also, in the tips section of this very forum are fingering charts for all four major pitches of tubas.
What is your tuba? That might shed more light. Also, in the tips section of this very forum are fingering charts for all four major pitches of tubas.
Jupiter JTU1110
"Real" Conn 36K
"Real" Conn 36K
- hbcrandy
- 4 valves

- Posts: 653
- Joined: Wed Apr 21, 2004 10:28 pm
- Location: Baltimore, Maryland USA
- Contact:
There are several flavors of fifth valves. The most common today is the flat whole step. There is also the half-step fifth valve. The older German rotary valved tubas such as Miraphone and Meinl Weston, originally were equipped with 1 1/2-step descending fifth valves.
Randy Harrison
Proprietor,
Harrison Brass
Baltimore, Maryland USA
http://www.harrisonbrass.com
Instructor of Applied Brass Performance
Maryland Conservatory of Music
Bel Air and Havre de Grace, Maryland USA
http://www.musicismagic.com
Proprietor,
Harrison Brass
Baltimore, Maryland USA
http://www.harrisonbrass.com
Instructor of Applied Brass Performance
Maryland Conservatory of Music
Bel Air and Havre de Grace, Maryland USA
http://www.musicismagic.com
- Art Hovey
- pro musician

- Posts: 1508
- Joined: Sun May 02, 2004 12:28 am
- Location: Connecticut
As a starting point, see Example 2:
http://www.galvanizedjazz.com/tuba/5thvalve.html
A one-and-one-half step fifth valve is unusual; that would be a minor third, the same as a conventional third valve. Is that really what you have?
http://www.galvanizedjazz.com/tuba/5thvalve.html
A one-and-one-half step fifth valve is unusual; that would be a minor third, the same as a conventional third valve. Is that really what you have?
-
Sean Kennedy
- lurker

- Posts: 13
- Joined: Sun Jun 11, 2006 11:09 pm
- Location: Albuquerque, NM/Santa Fe, NM
- porkchopsisgood
- pro musician

- Posts: 243
- Joined: Fri Mar 19, 2004 1:55 am
- iiipopes
- Utility Infielder

- Posts: 8580
- Joined: Tue Sep 06, 2005 1:10 am
So, is this to go along with 3 being pulled to make 23 in tune, or with 3 as two full steps?porkchopsisgood wrote:The "flat 1st" configuration is what we are used to seeing here in the States, but the "min 3rd" configuration is not at all unusual.
Use your ear....or check some German sites....
Enjoy!
Jupiter JTU1110
"Real" Conn 36K
"Real" Conn 36K