Buy new or Restore old?
-
- lurker
- Posts: 10
- Joined: Fri Jan 26, 2018 1:55 pm
- Location: Northeast Ohio
Buy new or Restore old?
This is a debate I've been having with myself for some time. I have a VERY old "Sonora" B+S copy Bb 4-valve horn that is playable but has issues. Namely:
-Leadpipe needs replaced (prior patch near the shank, has major dents, and could probably be realigned as per next issue)
-The body has been compressed throughout, to the point the 2nd slide is unable to pulled.
-Major dents throughout outer bows.
-The nickle finish has been eaten away to a dull, rough state. (Not a issue)
-It needs a chem clean, the rotors were cleaned about a year ago to make it playable.
Compression on the rotors seem great as far as I can tell. The partials -may- be a bit wonky, either because I am a Euph player or because of imperfections in the instrument.
Bottom line, for the same price would I get a better instrument having the Sonora entirely overhauled (completely realigned, the whole 9 yards), or buying a new/used horn? I did not get an estimate on the overhaul, but I'm assuming between $800-1600 without plating (based on prior dealings with the tech).
-Leadpipe needs replaced (prior patch near the shank, has major dents, and could probably be realigned as per next issue)
-The body has been compressed throughout, to the point the 2nd slide is unable to pulled.
-Major dents throughout outer bows.
-The nickle finish has been eaten away to a dull, rough state. (Not a issue)
-It needs a chem clean, the rotors were cleaned about a year ago to make it playable.
Compression on the rotors seem great as far as I can tell. The partials -may- be a bit wonky, either because I am a Euph player or because of imperfections in the instrument.
Bottom line, for the same price would I get a better instrument having the Sonora entirely overhauled (completely realigned, the whole 9 yards), or buying a new/used horn? I did not get an estimate on the overhaul, but I'm assuming between $800-1600 without plating (based on prior dealings with the tech).
Willson 2950 - Schilke 52E2
"Sonora" Bb 4 rotor - Bach 18
Conn 88HO - Schilke 51D
"Sonora" Bb 4 rotor - Bach 18
Conn 88HO - Schilke 51D
- Ken Crawford
- 4 valves
- Posts: 722
- Joined: Sat Jun 23, 2012 10:45 am
- Location: Rexburg, ID
Re: Buy new or Restore old?
You won't be able to buy a better tuba for $1600. But in the end you'll have a tuba that might be worth $1600. So really the question is: Do you want a better tuba than a $1600 tuba?
-
- 5 valves
- Posts: 1525
- Joined: Mon Aug 02, 2010 3:12 pm
- Location: USA
Re: Buy new or Restore old?
The old B&S 101/'Sonora' was one of the best 4/4 4rv BBb tubas made The Chinese copies of that horn vary and tend to be good, but none match the original. You may be able to buy a used good Chinese B&S clone AND do a decent econo-overhaul on your real-deal B&S 'Sonora' for $1600
There was a clone for sale not too long ago near your area in the classifieds -- the seller was only asking $800 for the tuba & case.
There was a clone for sale not too long ago near your area in the classifieds -- the seller was only asking $800 for the tuba & case.
-
- lurker
- Posts: 10
- Joined: Fri Jan 26, 2018 1:55 pm
- Location: Northeast Ohio
Re: Buy new or Restore old?
Ken - Of course! ...but as a doubler who is still working up his chops, I'm trying to be realistic with my budget. I lucked into this one on the cheap, and so I'm trying to weigh out how far this one might take me.
I know the B&S horns have been well spoken of on the forum, which is why I'm considering the overhaul. Perhaps the better question is What is a new horn that is comparable to the B&S ones?
I know the B&S horns have been well spoken of on the forum, which is why I'm considering the overhaul. Perhaps the better question is What is a new horn that is comparable to the B&S ones?
Willson 2950 - Schilke 52E2
"Sonora" Bb 4 rotor - Bach 18
Conn 88HO - Schilke 51D
"Sonora" Bb 4 rotor - Bach 18
Conn 88HO - Schilke 51D
-
- lurker
- Posts: 10
- Joined: Fri Jan 26, 2018 1:55 pm
- Location: Northeast Ohio
Re: Buy new or Restore old?
Enjoy.
https://imgur.com/gallery/Nx0tmSL
Picture#3-Lead pipe patch, tried to show 2nd slide angled into the body.
Picture#4-The light square is where I pulled a piece of tape off and the original finish is still intact. It's even raised slightly, making me think the rest of the finish has been striped.
EDIT- Added link to the album on imgur, rather than the massive pictures stretching the page. Always shrink images prior to uploading, D'OH
https://imgur.com/gallery/Nx0tmSL
Picture#3-Lead pipe patch, tried to show 2nd slide angled into the body.
Picture#4-The light square is where I pulled a piece of tape off and the original finish is still intact. It's even raised slightly, making me think the rest of the finish has been striped.
EDIT- Added link to the album on imgur, rather than the massive pictures stretching the page. Always shrink images prior to uploading, D'OH
Willson 2950 - Schilke 52E2
"Sonora" Bb 4 rotor - Bach 18
Conn 88HO - Schilke 51D
"Sonora" Bb 4 rotor - Bach 18
Conn 88HO - Schilke 51D
-
- 5 valves
- Posts: 1716
- Joined: Fri Jul 20, 2012 10:42 pm
- Location: Baltimore, MD, USA
Re: Buy new or Restore old?
I'll second fixing the Sonora. Nothing there that can't be fixed, and you'll have a very good tuba when it's done.
Principal tuba, Bel Air Community Band
Old (early 1900s?) Alexander BBb proto-163
1976 Sonora (B&S 101) 4-rotor BBb
1964 Conn 20J/21J BBb (one body, both bells)
1970s Marzan Slant-rotor BBb
~1904 York 3P BBb Helicon
Old Alex Comp.F, in shop
Old (early 1900s?) Alexander BBb proto-163
1976 Sonora (B&S 101) 4-rotor BBb
1964 Conn 20J/21J BBb (one body, both bells)
1970s Marzan Slant-rotor BBb
~1904 York 3P BBb Helicon
Old Alex Comp.F, in shop
- The Big Ben
- 6 valves
- Posts: 3169
- Joined: Sat Dec 16, 2006 11:54 am
- Location: Port Townsend, WA
Re: Buy new or Restore old?
Next trip is to the tech to see if he will indeed fix it like you want it at a price you want to pay.
-
- lurker
- Posts: 10
- Joined: Fri Jan 26, 2018 1:55 pm
- Location: Northeast Ohio
Re: Buy new or Restore old?
....I never even considered the possibility of ordering parts for it. Definitely would try the clone route first, I've read other recent endeavors attempting to get parts from B+S I'd resigned to the fate of having to have a new lead pipe manually bent to fit, so Bloke may have just saved me $$$
The 4th tube looks worse in the picture than in person. It's probably about 1/4 or 1/3 of the diameter at the worst spots.
It's reassuring to hear such the votes for fixing it. The downside is, that means all the quirks and missed notes are truly my fault
The 4th tube looks worse in the picture than in person. It's probably about 1/4 or 1/3 of the diameter at the worst spots.
It's reassuring to hear such the votes for fixing it. The downside is, that means all the quirks and missed notes are truly my fault
Willson 2950 - Schilke 52E2
"Sonora" Bb 4 rotor - Bach 18
Conn 88HO - Schilke 51D
"Sonora" Bb 4 rotor - Bach 18
Conn 88HO - Schilke 51D
-
- 5 valves
- Posts: 1525
- Joined: Mon Aug 02, 2010 3:12 pm
- Location: USA
Re: Buy new or Restore old?
^ After looking at your Sonora pics, you might be being a little hard on yourself. That leadpipe/mouthpipe looks toast to me, it is pretty much 'crushed'. I'm pretty sure it is messing with the playability.
Like bloke said, get in contact with Tom @ Mack Brass to replace that old leadpipe. Show him this thread and he may be willing to sell you a Mack 200 BBb leadpipe to fit your Sonora.
Good luck
Like bloke said, get in contact with Tom @ Mack Brass to replace that old leadpipe. Show him this thread and he may be willing to sell you a Mack 200 BBb leadpipe to fit your Sonora.
Good luck
-
- pro musician
- Posts: 147
- Joined: Fri Mar 19, 2004 9:04 am
Re: Buy new or Restore old?
I was recently faced with this decision concerning my GDR PT10. It got smashed up and I was considering: a) a new bell, b) fix existing horn, c) new tuba all together. Ultimately, I decided on a complete tear down because I really like the horn-even damaged. I reached out to Bob Tucci and will say if I had gone with option “a” Bob could not have made it easier. As for buying a new tuba, they’re expensive and don’t do for me what my existing equipment does.
Ask yourself how much you like the positives v. hate the negatives. Your answer lies in the numbers.
JMO, YMMV
Ask yourself how much you like the positives v. hate the negatives. Your answer lies in the numbers.
JMO, YMMV
- Donn
- 6 valves
- Posts: 5977
- Joined: Fri Aug 19, 2005 3:58 pm
- Location: Seattle, ☯
Re: Buy new or Restore old?
I've never bought a leadpipe, do they come ready to solder on? I had a notion somehow that they come out of the box straight.TD517 wrote:I'd resigned to the fate of having to have a new lead pipe manually bent to fit, so Bloke may have just saved me $$$
I agree about the outcome - an uncrushed leadpipe is bound to make a very noticeable improvement.
- The Big Ben
- 6 valves
- Posts: 3169
- Joined: Sat Dec 16, 2006 11:54 am
- Location: Port Townsend, WA
Re: Buy new or Restore old?
I had a new Miraphone mouthpipe put on a 186 and it came from MP bent. It did need to be tweaked a little bit to get it just so. Chances are good that even a "clone" mouthpipe is going to have to be wrestled and tweaked to get it installed. Too many variables to think it would just "go on".Donn wrote:I've never bought a leadpipe, do they come ready to solder on? I had a notion somehow that they come out of the box straight.TD517 wrote:I'd resigned to the fate of having to have a new lead pipe manually bent to fit, so Bloke may have just saved me $$$
I agree about the outcome - an uncrushed leadpipe is bound to make a very noticeable improvement.
I've seen mouthpipes in the catalogs that are straight, filled with pitch/Cerrobend and I've seen flat pieces of sheet that were cut, bent, tapped, soldered and pounded and to make a custom mouthpipe. Labor charges would escalate for each step from a prebent mouthpipe.
Last edited by The Big Ben on Mon Feb 18, 2019 11:24 pm, edited 2 times in total.
- Dan Schultz
- TubaTinker
- Posts: 10424
- Joined: Thu Mar 18, 2004 10:46 pm
- Location: Newburgh, Indiana
- Contact:
Re: Buy new or Restore old?
I routinely refurb and offer those horns for sale for between $1,800 and $2,500 depending on the exact condition. Would I spend the same amount of money on a Chinese horn? HELL NO!
Dan Schultz
"The Village Tinker"
http://www.thevillagetinker.com" target="_blank
Current 'stable'... Rudolf Meinl 5/4, Marzan (by Willson) euph, King 2341, Alphorn, and other strange stuff.
"The Village Tinker"
http://www.thevillagetinker.com" target="_blank
Current 'stable'... Rudolf Meinl 5/4, Marzan (by Willson) euph, King 2341, Alphorn, and other strange stuff.
-
- lurker
- Posts: 10
- Joined: Fri Jan 26, 2018 1:55 pm
- Location: Northeast Ohio
Re: Buy new or Restore old?
My repair tech basically said the same things. Enough so that he was apprehensive about that route unless they still have the pitch in them, or "they can be returned when it doesn't fit". Hmmm...The Big Ben wrote:Chances are good that even a "clone" mouthpipe is going to have to be wrestled and tweaked to get it installed. Too many variables to think it would just "go on".
He also mentioned that most suppliers don't make mouthpipes that long anymore. He could splice two together, but that doesn't seem optimal either.
Also, shout out to Dan, who is great. I got a stop plate from him for this tuba, very reasonably. Great guy, highly recommended!
Willson 2950 - Schilke 52E2
"Sonora" Bb 4 rotor - Bach 18
Conn 88HO - Schilke 51D
"Sonora" Bb 4 rotor - Bach 18
Conn 88HO - Schilke 51D
-
- 5 valves
- Posts: 1525
- Joined: Mon Aug 02, 2010 3:12 pm
- Location: USA
Re: Buy new or Restore old?
Yupbloke wrote:I don't ever expect parts like that - even if made by the original manufacturer - to lay right into place.
Tuba repairs are more than parts-changing.
I'm nearly certain that those two Jinbao-made parts could be convinced to fit, and to be made to look as if originally fit.
The Jinbao-made mouthpipes still have pine-tar pitch in them, and they are made in one long piece -- I should know because I bought a couple of them several years ago for a couple old tubas I have.TD517 wrote:My repair tech basically said the same things. Enough so that he was apprehensive about that route unless they still have the pitch in them, or "they can be returned when it doesn't fit". Hmmm...The Big Ben wrote:Chances are good that even a "clone" mouthpipe is going to have to be wrestled and tweaked to get it installed. Too many variables to think it would just "go on".
He also mentioned that most suppliers don't make mouthpipes that long anymore. He could splice two together, but that doesn't seem optimal either.
If your brass tech is STILL apprehensive to "do the job" with the already-bent/already-filled B&S copy mouthpipe, it may be time to look for another tech to do the job....
Either way, a new mouthpipe/leadpipe will most likely have to be 'tweaked' (slight bending, cutting, etc) to fit your horn anyway. And they will have to melt out the pitch (duh) and round out the ends before soldering it onto the tuba
-
- TubeNet Sponsor
- Posts: 862
- Joined: Fri Apr 09, 2004 7:22 am
- Location: Virginia
- Contact:
Re: Buy new or Restore old?
bloke wrote:Personally, I like those instruments more than the Jinbao copies of them (though the Jinbao copies are light years better than they were when I first saw them in the 1980's).
As a no-brainer (if I wished to own a tuba of this size/configuration) I would repair the B&S-made instrument but (well...) I wouldn't charge myself anything to do it.
Ask Tom McGrady if he might order you a replacement mouthpipe for a Jinbao model 200...or ask B&S (and good luck with that). If that thumb-sized dent in the lower #4 circuit tubing is epic, you might also ask Tom for that part.
I do have these in stock.
Tom McGrady
MACK Brass of Virginia LLC
Email: Sales@mackbrass.com" target="_blank
http://www.mackbrass.com" target="_blank" target="_blank
804-926-7707
MACK Brass of Virginia LLC
Email: Sales@mackbrass.com" target="_blank
http://www.mackbrass.com" target="_blank" target="_blank
804-926-7707